ZKJ-410C角行程電動執行機構（電動門）回路校線  

用通燈檢查電動執行機構（電動門）線路保證線路正確率為同時檢查線號標志字跡應端正、清晰、不褪色，內容正確，書寫方向一致。角行程電動執行機構（電動門）回路校線完成后由技術員和施工人員負責自檢并填寫電動執行機構（電動門）回路校線施工記錄 。 

ZKJ-410C角行程電動執行機構電動執行機構（電動門）調試  

ZKJ-410C角行程電動執行機構電動執行機構（電動門）送電源前，先用500V搖表測量電動執行機構（電動門）控制回路和電機絕緣應合格(大于等于1兆歐)，然后用萬用表測量電機的三相繞組電阻是否一致，用萬用表檢查限位開關、轉矩開關、開按鈕、關按鈕等配接線是否正確，確認無錯誤后手動對電動門做一次全行程往復走動，確保行程開關正常動作后，接上電源并把開關打到試驗位，進行回路試動作，檢查開、關行程開關及開、關、停按鈕動作時回路是否正確動作。  

電機試動：將電動門手動搖到中間位置按動開或關按鈕后馬上按停止按鈕，同時觀察電動門開關方向，若開關方向與按按鈕一致，表示電機旋轉方向正確；若反方向則任意調換電機端子盒或接線盒中的兩根電源接線。 

限位開關設定：電動將閥門關到即將關閉位置，然后手動將閥門搖到關閉，然后向回轉1~2圈，用螺絲刀調整至關限位開關剛好動作，用萬用表測量限位開關輸出接點信號正確；開限位開關設定方法同上。  

轉矩開關設定：轉矩開關已由廠家設定好，不需要調整，可用測試旋鈕測試：當電機旋轉時，用螺絲刀調整測試旋鈕，如果控制電機的接觸器失電，則控制電路是正確的，如果不失電，應立即切斷電源，檢查控制回路改正配線。 

電動調整門限位開關、轉矩開關調整方法和步驟同上。限位開關、轉矩開關調整完后，觀察閥門開關方向和開度指示，同時將萬用表串入反饋信號回路，調整微調旋鈕，閥門開度就地指示和反饋信號一致為止。 

電動執行機構調試方法和步驟與電動門基本相同。  

電動執行機構（電動門）就地調試完成后，做一次全行程開關動作，同時用秒表測量全行程開關動作時間，并作好調試記錄。

.電動執行機構（電動門）調試完成后由技術員和施工人員負責自檢并填寫電動執行機構（電動門）調試施工記錄 ，報熱控施工處質檢員進行檢驗。